RFID on-metal tags: metal, liquid and read-zone analysis before installation
RFID tags on metal and liquid: why does reading drop, which tests come before installation, and how is the read zone calibrated? With a checklist.
Using RFID tags on metal needs special care: metal reflects the radio signal and liquid absorbs it, so read range and read rate can drop. Before installation, measure on site the product type, tag position, way of passing through and environmental interference, and calibrate the read zone so that it reads only the target area. The checklist below puts these tests in order.
The sample tags the supplier brought read perfectly on the trial table in the office. The project was approved and the readers were installed. When shipping began, the picture changed: metal shelves, cartons full of drinks and another reader working in the next aisle came into play, and the count results began to differ from day to day. The culprit is usually not the tag or the reader but the site itself. In RFID, most of the success is decided before installation, in measurements taken in the real environment. This article offers a checklist that puts those measurements in order.
Site analysis is the preliminary study in which product type, tag position, the effect of metal and liquid, the way products pass through and environmental interference are measured in the real environment before an RFID installation. If a tag is going to be stuck on metal, work only with tags designed for metal and the right position; do not assume an ordinary tag will read well on metal.
Why do metal and liquid disturb an RFID read?
UHF RFID works with radio waves, and radio waves interact with the environment. Metal surfaces reflect the signal, which creates strong and weak zones in the read field. If a tag is stuck directly onto metal, its antenna is also detuned and it often gives almost no answer at all. Liquid absorbs part of the signal; in beverage, cosmetic or food products, the contents behind the tag can weaken the read. The table below pairs the symptoms seen most often in the field with their likely causes.
| Symptom | Likely cause | What to try in the field |
|---|---|---|
| Read range shorter than expected | Tag too close to metal or liquid; antenna power or direction not suitable | Move the tag away from the surface, try a tag designed for metal, change the antenna direction |
| Some tags are not read at all | Tags are stacked on top of one another and shadow each other; the tag’s orientation does not suit the antenna | Change the stack arrangement and tag position, try different orientations |
| Read rate changes from day to day | Metal objects around, other readers nearby or machines create interference | Measure again at different times, temporarily switch off the neighboring reader and compare |
| Tags in the next area are also read | Antenna power higher than needed, read zone not isolated | Reduce the power, narrow the antenna angle, add physical isolation |
| Tags are missed at fast pass-through | The product stays in the read field too briefly | Slow the pass-through speed, lengthen the zone or increase the number of antennas |
| Weak reads on products containing liquid | The liquid absorbs the signal | Move the tag to a surface away from the liquid, try a different tag form |
A fictional example: the shipping gate of a beverage warehouse
An RFID reader will be installed at the shipping gate of a beverage warehouse. The cartons are cardboard, but inside are bottles full of liquid; the shelves beside the gate and the freight elevator are metal. In the site analysis, the first job is to pass the same carton through the gate with the tag in three different positions: on the side face, on the top face and at the corner. Then the cartons are tried as a stacked pallet, at normal speed and while a forklift is driving. Finally, it is checked whether the pallet in the aisle opposite the gate is also read. The results of these three measurements decide which surface the tag will be stuck on and how far the reader power can be turned up; and they do so before installation, while the fix is still cheap.
How is an on-metal tag used?
Use on metal is a separate class of tag and is generally based on the principles below. The result of each must be tried on your product.
- Choose a tag designed for metal. A tag with a structure that takes the effect of metal into account behaves differently from an ordinary tag on the same surface.
- Consider leaving a gap between the surface and the tag. Some tag types provide this gap with a spacer layer or a hard body.
- Fix the tag’s orientation and position. A tag stuck in a different place on every product makes the measurement impossible to repeat.
- Treat liquid containers and metal packaging as separate product classes. Even if they pass through the same tunnel, handle them with separate tests.
Which tests are done on site before installation?
- Take a real product sample. Use the carton, pallet or hanger that actually flows on site, not a catalog product.
- Place the tag in trial positions. Read the same product with several different positions and note the results.
- Test with the real way of passing through. At a tunnel, gate or handheld terminal, read at the product’s normal speed and direction; a test done while standing still will not show a speed problem.
- Measure the neighboring area. Separately check whether tags in places that should not be read are being read.
- Look for environmental interference. Measure with working machines, metal shelves and other readers on and off.
- Repeat at different times and fill levels. An empty warehouse and a full one, the morning shift and the evening shift, may not give the same result.
- Record the results with photos and notes. If it is not written down which tag, which position, which power and which result, the measurement cannot be repeated.
How is the read zone calibrated?
The aim is not “reading as far as possible” but reading only the tags in the target area reliably. Calibration sets this balance: the reader, antenna, power and physical isolation are adjusted so that the wanted zone is covered and the neighboring zone is left out.
- Keep the power at the level that reads the farthest tag in the target area; power higher than needed makes the neighboring zone read too.
- Set the antenna direction and angle according to the direction in which the product passes.
- If needed, limit the read field physically with metal or absorbing material.
- Store the setting as a fixed record; if someone changes it after installation, know why.
A checklist for site analysis
The list below can be filled in for each read point before installation.
- Product type and material (cardboard, fabric, plastic, glass, metal, containing liquid) noted.
- Tag type and the position it is attached to determined separately for each product group.
- Metal surfaces, shelves and machines located and marked relative to the read point.
- Product groups containing liquid tested separately.
- The product’s way of passing through (tunnel, gate, handheld terminal, station), its speed and direction recorded.
- Whether tags in neighboring areas are read by mistake tried.
- Other readers and sources of interference in the surroundings listed.
- Measurement repeated at different times and fill levels.
- Settings (power, antenna direction) and results entered in the record.
- The validation rule to be applied at the edge layer decided: expected product, location, repeat filtering.
Keeping site notes in Excel and photos
For a single read point, recording the measurement results in Excel and in photos is enough. The problem starts when there are several points, shifts and tag types: which result was taken with which setting gets confused, the old measurement stays valid after a change, and nobody knows who changed the setting. Keeping the site information in a single record together with the settings and results makes it easier both to go back when a problem comes up and to apply the same method at a new point.
Site analysis in the YazSis RFID approach
YazSis RFID & IoT systems work with four principles: measure the site, calibrate the read zone, validate at the edge layer, connect to the system. The first principle covers exactly the work in this article: product type, tag position, the effect of metal and liquid, the way of passing through and environmental interference are analyzed on the spot. Then the reader, antenna, power and physical isolation are set so that only the tags in the target area are read reliably. The raw signal becomes a meaningful operation at the edge layer through repeat checking, business rules and product matching.
If you would like to talk about how we could set up a site analysis for your own warehouse, production or shipping point, you can reach us from the RFID & IoT systems page.
Frequently asked questions
What happens if an RFID tag is stuck on metal?
An ordinary tag is detuned on a metal surface and is often read very weakly or not at all. Tags designed for metal surfaces, the right position and, if needed, a gap from the surface are required.
Why do metal and liquid cause problems in RFID reading?
Metal reflects the radio signal and creates weak zones in the read field; liquid absorbs part of the signal. Both make it harder for the tag to take energy and answer.
Why do RFID read range and read rate drop?
Besides the effect of metal and liquid, the orientation of the tag, stacking, other readers or machines nearby, the antenna setting and the speed at which the product passes can reduce read range and rate. The cause is found by trying things one by one on site.
Which tests are done on site before an RFID installation?
With a real product sample, tests are done on tag position, way of passing through, neighboring area, environmental interference and different times and fill levels; settings and results are entered in the record.
Is site analysis necessary for every RFID project?
If the products are easy materials such as cardboard or fabric, the analysis can be lighter, but it becomes indispensable where there is metal, liquid or a dense environment. Even a small preliminary measurement reduces the cost of correction after installation.
More articles
What drives custom software cost? Custom software pricing and how to read a quote
Three quotes for the same custom software need can differ widely, and that is no surprise. We explain the factors behind the cost, the questions to ask when reading a quote and a comparison table, without quoting any figures.
November 16, 2026 · 8 min readMobile app development cost and pricing: the key cost items in an enterprise app
Mobile app pricing cannot be reduced to a single figure; it depends on the items that make up the scope. We list the items that drive the cost of an enterprise field app and what you should put in writing before asking for quotes.
November 16, 2026 · 8 min readWhat is an internal audit and how is it done? ISO audit programme, report example, closure
What is an internal audit? It is how you check, from the inside, whether your management system works as written. How to build the programme, what the report contains and how a finding is closed: a simple framework.
November 16, 2026 · 8 min read