How to track calibration: instrument list, due dates and out-of-tolerance results

Calibration tracking means following the verification dates and results of measuring instruments on record. The instrument list, the steps and common mistakes.

FUFerhat UğurluYazSis TeamPublished: November 22, 20266 min read

Calibration tracking is the process of keeping a record of when each measuring instrument in the company was verified, what the result was and when the next verification is due. Instruments such as scales, calipers, micrometers, pressure gauges, thermometers or torque wrenches drift over time; if the drift goes unnoticed, every measurement taken with that instrument, and every decision based on it, becomes questionable. A sound tracking routine rests on three things: a complete instrument list, an owner for each instrument and an alert that announces the approaching date in advance. A tool such as the Reminder Module, which follows dates with repeat rules, takes this work out of people’s memory.

Why does calibration tracking break down?

In most companies calibration dates live in a spreadsheet or on the label attached to the instrument. One person updates the spreadsheet; when that person goes on leave or changes role, the dates lose their owner as well. The label only informs whoever walks up to the instrument and gives the manager no overall view. The problem usually surfaces just before an audit or a customer complaint: overdue instruments are hunted down and documents are searched for in folders. The purpose of tracking is to remove this rush and make the situation visible every day.

The instrument list: the basis of tracking

An instrument that is not on the list cannot be tracked. The first job is to put every instrument whose readings are trusted for decisions into a single list. The spare caliper in a workshop drawer and the precision balance in the laboratory belong on the same list. For each instrument it is enough to keep the following information:

  • Name, make, serial number and the identification number given by the company
  • Location and the department that uses it
  • The person responsible for the instrument
  • Measuring range and the job it is used for
  • Last calibration date, its result and where the document is kept
  • Next calibration date
  • Status: in use, at calibration, out of use

How is the calibration interval set?

Choosing the same interval for every instrument is easy but often not right. When setting the interval, look at the manufacturer’s recommendation, how often and under what conditions the instrument is used, the effect of the measurement on product quality and the previous calibration results. An instrument used in the field every day does not wear in the same way as one taken out once a month. If previous results are repeatedly well inside the limits, the interval can be reviewed; if they are approaching the limit, shortening it is the safer choice. If your sector or your customer contract sets a separate condition, that condition takes priority; consult your quality manager on this.

Calibration tracking step by step

  1. Draw up the list. Walk through the departments one by one and record the instruments kept in drawers and cabinets too.
  2. Assign an owner. Every instrument should have one; write a person’s name rather than a general label such as “quality department”.
  3. Enter the date and the repeat rule. Define the next calibration date and how many months apart it repeats.
  4. Set an advance alert. Sending the instrument to a laboratory and getting it back takes time; the alert must arrive early enough to arrange a spare instrument.
  5. Plan the dispatch. Group instruments that fall due in the same period, but sequence them so that production is not left without instruments.
  6. Record the result. When the instrument returns, enter the date, the result and the document; the next date should be renewed accordingly.
  7. Update the label. The label on the instrument and the record must show the same date.

What if the result is out of tolerance?

This is the part of tracking that is skipped most often. If an instrument comes back from calibration with an “out of tolerance” result, the job does not end with having it adjusted or replaced. The real question is this: in which measurements has this instrument been used since the previous calibration? To answer it, the job and the department in which the instrument is used must be on record. In such a case the following steps are taken:

  • The instrument is taken out of use immediately and its status is changed in the record.
  • The jobs and products measured with the instrument are identified and the extent of the effect is assessed.
  • Products for which it is considered necessary are measured again.
  • The decision taken is written into the instrument’s history with its owner and date.
  • The calibration interval of the instrument is reassessed.

Common mistakes

  • Looking only at the date. The arrival of the document is not enough; someone must read whether the result is within the acceptance limits.
  • Not adding a newly bought instrument to the list. If there is no link between purchasing and the instrument record, the list soon becomes incomplete.
  • Waiting with a dropped or knocked instrument. Even if its date has not come, such an instrument should not be used before it is checked.
  • Leaving an out-of-use instrument lying around. Without a clear mark on it, someone will certainly use it.
  • Sending all instruments on the same day. Production can no longer measure; dispatch must be planned in stages.

Keeping the date and the history in one record

It is possible to start with a spreadsheet; as the number of instruments and departments grows, it matters more that the alert arrives by itself and the history sits in one place. The Reminder Module of YazSis KurumsalPortal follows inspection, licence, contract, maintenance and control dates with repeat rules; it gives staged advance alerts 30, 7 and 1 day before the critical date by portal notification, e-mail and SMS, and records completed controls together with their history. Calibration dates can be followed in the same way, as periodic control records. For the breakdown, repair and cost of an instrument, the Maintenance & Fault Management module keeps the fault record, technician assignment and equipment history together.

Calibration tracking does not require a large investment; a complete list, a named owner and an alert that arrives in time solve most of the work. To see how you can follow dates and periodic controls in a shared record, you can review the KurumsalPortal page.

Frequently asked questions

What is calibration tracking?

Calibration tracking is the process of keeping a record of when measuring instruments were verified, the result and the next verification date. The aim is to prevent an overdue or out-of-tolerance instrument from being used unnoticed.

What determines the calibration interval?

The manufacturer’s recommendation, how often and under what conditions the instrument is used, the effect of the measurement on product quality and previous calibration results are assessed together. If your sector or customer contract sets a separate condition, that condition applies.

What is the difference between calibration and maintenance?

Maintenance keeps the instrument in working order. Calibration compares the value the instrument shows with a reference. The two should be followed as separate records with separate dates.

What should be done if an instrument returns from calibration with an unsuitable result?

The instrument is taken out of use, the measurements it has been used for since the previous calibration are identified, and products for which it is considered necessary are measured again. The decision is written into the instrument’s history.

Does KurumsalPortal remind you of calibration dates?

The Reminder Module of YazSis KurumsalPortal follows maintenance and control dates with repeat rules and sends alerts 30, 7 and 1 day before the date by portal, e-mail and SMS. Calibration dates can be defined in this way as periodic control records.

FU
Ferhat Uğurlu · YazSis Team

Builds enterprise software, AI and digital transformation products together with the YazSis team.